Electro-Harmonix EHX OD Glove Nano Overdrive Distortion Pedal

Rich, overtone laden sound that doesn’t get muddy. Responsive controls that
take you from sparkling, clean boost through brown crunch and all the way to
thick, saturated hi-gain. Advanced features like Tone Shift and selectable 9 or
18V internal voltage for surgical sound sculpting. The new OD Glove delivers
overdrive and distortion with impact, and the modern player in mind.

Quick Specs - Versatile MOSFET overdrive/distortion - Tone Shift switch -
Selectable 9V or 18V internal voltage - True bypass - Tough, compact die-cast
chassis - 9 Volt battery included - Optional 9.6DC-200 power supply available -
Dimensions in inches: 2.75 (w) x 4.5 (l) x 2.1 (h) - Dimensions in mm: 70 (w) x
115 (l) x 54 (h)

- CONTROLS -
GAIN Knob – Controls the amount of input gain and overdrive. As you turn this
knob clockwise, the OD GLOVE ranges from sweet cleans to full-power distortion.

TONE Knob – The TONE knob on the OD GLOVE filters out high frequencies. When
fully clockwise, the full tonal range of the overdrive comes through. As the
knob is turned counter-clockwise, high frequencies are rolled off. Use this to
achieve a smoother tone or to reduce any high-frequency harshness.

VOL Knob – Sets the output level of the OD GLOVE.

TONE SHIFT Switch – This switch controls the mid-frequency emphasis of the
TONE knob. Setting this switch to OFF creates a flatter EQ, with some emphasis
on low mids. Setting the SHIFT switch to ON emphasizes mids and high mids.
There is also a small increase in volume when the switch is set to ON.

FOOTSWITCH and LED – The Footswitch selects whether the OD GLOVE is engaged or
in true bypass mode. When the effect is engaged, the LED is lit.

INPUT Jack – This ¼” jack is the audio input for the OD GLOVE. The input
impedance is 300kOhm.

AMP Jack – This ¼” jack is the audio output from the OD GLOVE. The output
impedance depends on the VOLUME setting, ranging from 12kOhm to 100kOhm.

9V Power Jack – The OD Glove can run off of a 9V battery or you can use an
optional 9VDC AC Adapter capable of delivering at least 50mA to the 9V power
jack. We recommend the EHX9.6DC-200. The AC Adapter must have a center negative
plug. The battery may be left in or taken out when using an AC Adapter. The OD
Glove draws 12mA at 9VDC. The maximum voltage that may be connected to the 9V
Power Jack is 10VDC.

INTERNAL VOLTAGE SWITCH – The OD GLOVE includes an internal slide switch to
change its internal power supply voltage from 9V to 18V. Operation at 18V
results in a less compressed, more open tone that may work better for some
guitar/amplifier combinations. Operation at 9V results in a tighter sound, and
reduces the current draw to 5mA. Experiment with the voltage setting at full
volume to find the best sound for your playing style. Please remember: do not
exceed 10VDC at the 9V Power Jack. The OD Glove generates the 18V internally.

To select the operating voltage, remove the four screws on the bottom of the
OD GLOVE and take off the bottom plate. There is a slide switch near the input
jack labeled “Voltage Select.” Slide this switch to the right for normal 9V
operation. Slide it to the left for 18V operation. You do not need to change
the battery or adapter when changing the internal voltage.

- CHANGING THE BATTERY -

To change the battery, remove the four screws on the bottom of the OD GLOVE
and take off the bottom plate. The battery clip is in the bottom of the unit.
Take care not to touch the circuit board while changing the battery in order to
avoid damaging a component.